Loading...
Experimental and numerical investigation of heat treatment of al-si-cu alloy
Author(s)
Cupido, Llewellyn Heinrich
Date Issued
2014
Type
Thesis
Publisher
Cape Peninsula University of Technology
Abstract
Aluminium alloys has seen recent increase usage in the automotive industry. This is due to the global obligation towards carbon emission reduction and fuel efficiency in the transport sector. The good strength-to-weight ratio offered by Al-Si-Cu alloys showed promising results towards the compliance of these environmentally friendly criteria.
The enhanced mechanical properties is obtained when the alloy is subjected to the T6 heat treatment process, which cause microstructural changes due to the evolution of intermetallic phases. The process involves solution heat treatment, for dissolving soluble Cu- and Mg-containing phases, the homogenization of alloying elements, and the spheroidisation of eutectic Silicon. It is followed by quenching, for maximum precipitation hardening particle retention in solution, and a further artificial ageing process with the aim to acquire a uniform distribution of small precipitates, for strength improvement.
The heat treatment schedule applied in this study was conducted as follows: Solution heat treatment at a temperature of 525°C for 6h Quenching in water of temperature 50°C; Artificial ageing for 8h at a temperature of 175°C, and then after left inside furnace to cool down to room temperature. This is higher than the 520°C, but shorter than the 8-12h, observed in literature. Also, quenching is done at a lower temperature rather than 60°C, and artificial ageing at a higher temperature, rather than the 155°C. This was done to be able to draw a comparison between the MAGMASOFT® simulation, which has this non-adjustable schedule, and the experimental results.
The simulated and experimental results were comparable and similar outcomes, but with some discrepancies. Such as the porosity was far more visible and intense in the experimental, than what was predicted by the software. The as-cast and heat treated microstructure revealed the expected evolution of intermetallic particles, such as dissolving of the Al2Cu and the spheroidisation of the eutectic Si phases. Another phase that was identified was the insoluble AlFeSi and other possible Fe-containing phases, which due to the higher solution heat treatment temperature, showed partial fragmentation and dissolution.
The study provided practical data about the effect of heat treatment on microstructural evolution and how it affects the properties of the Al-Si-Cu alloy. It also brought to the attention and understanding of how critical pouring temperature is, as it affect the initial nucleation, and cooling rate, and therefore the micro and macro properties.
The enhanced mechanical properties is obtained when the alloy is subjected to the T6 heat treatment process, which cause microstructural changes due to the evolution of intermetallic phases. The process involves solution heat treatment, for dissolving soluble Cu- and Mg-containing phases, the homogenization of alloying elements, and the spheroidisation of eutectic Silicon. It is followed by quenching, for maximum precipitation hardening particle retention in solution, and a further artificial ageing process with the aim to acquire a uniform distribution of small precipitates, for strength improvement.
The heat treatment schedule applied in this study was conducted as follows: Solution heat treatment at a temperature of 525°C for 6h Quenching in water of temperature 50°C; Artificial ageing for 8h at a temperature of 175°C, and then after left inside furnace to cool down to room temperature. This is higher than the 520°C, but shorter than the 8-12h, observed in literature. Also, quenching is done at a lower temperature rather than 60°C, and artificial ageing at a higher temperature, rather than the 155°C. This was done to be able to draw a comparison between the MAGMASOFT® simulation, which has this non-adjustable schedule, and the experimental results.
The simulated and experimental results were comparable and similar outcomes, but with some discrepancies. Such as the porosity was far more visible and intense in the experimental, than what was predicted by the software. The as-cast and heat treated microstructure revealed the expected evolution of intermetallic particles, such as dissolving of the Al2Cu and the spheroidisation of the eutectic Si phases. Another phase that was identified was the insoluble AlFeSi and other possible Fe-containing phases, which due to the higher solution heat treatment temperature, showed partial fragmentation and dissolution.
The study provided practical data about the effect of heat treatment on microstructural evolution and how it affects the properties of the Al-Si-Cu alloy. It also brought to the attention and understanding of how critical pouring temperature is, as it affect the initial nucleation, and cooling rate, and therefore the micro and macro properties.
Additional information
Thesis (MTech (Mechanical Engineering))--Cape Peninsula University of Technology, 2014
Subjects
File(s)![Thumbnail Image]()
Loading...
Name
203149998_cupido_l_mtech_mech_eng_2014.pdf
Description
Thesis
Size
5.03 MB
Format
Adobe PDF
Checksum
(MD5):78d77c1ef7ba60248541cc81d3c60b3c